What is a worm slew drive, and how does its ratio decide where your load stops? It is a slew drive that combines a slewing bearing, a housing, and a worm shaft that turns the bearing's gear ring. The reduction ratio is the number of worm shaft turns needed for one full turn of the output.
That one number sets output speed, angular resolution, the motor torque you need, and how much heat the gear mesh makes. This guide gives you a calculation-led workflow to pick a ratio at the specification stage, then check it before you release a drawing.
Inputs to Collect Before You Pick a Ratio
You cannot size a ratio from a catalog page alone. Gather the load and motion data first. Some items block the calculation, and others can wait until the detail design stage.
| Input | Why it matters | Blocks the calculation? |
|---|---|---|
| Peak load torque at the output (N·m) | Sets motor torque and the drive size | Yes |
| Required move angle and move time | Sets minimum output speed | Yes |
| Motor speed at the worm shaft (rpm) | Together with output speed, sets the ratio | Yes |
| Feedback type and counts per revolution | Sets theoretical resolution | Yes |
| Duty cycle (seconds moving per cycle) | Sets average heat load | Yes |
| Ambient temperature and sealing needs | Sets thermal margin and seal choice | No, can be refined later |
| Required accuracy and backlash limit | Decides single or double worm | Partly |
Wind, tilt, and inertia loads change peak torque. If you only know the static load, add a margin and mark it as an assumption on the spec sheet. In my design reviews, an unstated assumption causes more rework than a wrong number does.
Selection Method: Linking Reduction Ratio to Output Speed, Positioning Resolution, Motor Torque, and Duty-Cycle Heat
Work the four links in order. Each one filters the ratio range left by the previous step.
- Find the speed window. Output speed (rpm) = move angle ÷ 360 × 60 ÷ move time. Then ratio = worm shaft rpm ÷ output rpm. Any ratio that gives a slower output than required fails.
- Check resolution. Output step = 360° ÷ (feedback counts per motor rev × ratio). A higher ratio gives finer steps. Checkpoint: the step should be at least five to ten times smaller than your accuracy target.
- Calculate motor torque. Input torque = load torque ÷ (ratio × efficiency). Worm gearing is less efficient than spur gearing, and self-locking sets usually sit well below 50%. Use the efficiency on the drive datasheet, not a guess.
- Estimate heat. Heat while moving = input power − output power. Average heat = that value × duty fraction. Compare it with the drive's thermal limit and housing surface.
- Pick the ratio that passes all four. If none do, change the motor speed, add a pre-stage, or move to a larger frame.
The table below shows how each link moves when the ratio rises. A higher ratio is not automatically better.
| Ratio goes up | Output speed | Resolution | Motor torque needed | Heat risk |
|---|---|---|---|---|
| Effect | Falls | Finer | Falls | Can rise with longer move time and lower efficiency |
| Fits | Slow tracking, precise stops | Positioning and tracking | Small motors | Watch long, continuous duty |
| Does not fit | Fast repositioning | Accuracy limited by backlash, not counts | Cases with a hard speed target | Intermittent duty usually tolerates it |
Efficiency usually changes with ratio and lead angle. Treat the table as direction only, then rerun the numbers with datasheet values for each candidate.
Worked Example: A 1,000 N·m Positioning Axis
The numbers below are assumptions for illustration, not product data. Suppose you must rotate 90° in 6 seconds or less. Peak load torque is 1,000 N·m. The worm shaft turns at 150 rpm, and the motor encoder gives 4,096 counts per rev. Assumed efficiency is 0.40 for every option.
Required output speed: 90 ÷ 360 × 60 ÷ 6 = 2.5 rpm. The ratio is therefore 150 ÷ 2.5 = 60 at most.
| Candidate ratio | Output speed | Time for 90° | Output step per count | Input torque | Passes 6 s? |
|---|---|---|---|---|---|
| 40:1 | 3.75 rpm | 4 s | 0.0022° | 62.5 N·m | Yes |
| 60:1 | 2.5 rpm | 6 s | 0.0015° | 41.7 N·m | Just |
| 80:1 | 1.875 rpm | 8 s | 0.0011° | 31.3 N·m | No |
Now the heat check for 60:1. Input power is about 41.7 N·m × 15.7 rad/s ≈ 655 W. Output power is 1,000 N·m × 0.262 rad/s ≈ 262 W. The difference, about 393 W, becomes heat while moving. At a 25% duty fraction, average heat is close to 98 W.
The 60:1 option has zero timing margin. The 40:1 option leaves 2 seconds of margin, but it needs 50% more motor torque. Many designers pick the middle ground only after confirming the real motor speed and efficiency. The 0.0015° step is also a theoretical number. Real positioning error depends on backlash, housing stiffness, and bearing clearance, so the finest step does not buy accuracy by itself.
Request Your Custom Slew Drive or Bearing Spec
Tell us your load, speed, and environment — receive a tailored 100–5000 mm slewing drive or slewing bearing proposal with 3D drawings within 24 hours.
Common Ratio Mistakes and What They Look Like
- Choosing by resolution alone. The axis reaches the target late, or never reaches the move time. Fix: rerun step 1 of the method with the real motor speed.
- Using catalog efficiency from a different ratio. The motor stalls or overheats near peak load. Fix: ask for efficiency data at your exact ratio and load.
- Ignoring duty cycle. The housing runs hot after a long tracking shift, and the lubricant ages early. Fix: calculate average heat, not just peak torque.
- Counting on self-locking for dynamic holding. Vibration or shock can still creep the load. Fix: add a brake where safety depends on holding, and check with the manufacturer.
- Trusting encoder counts as accuracy. The display shows a fine step, but the load wanders by tenths of a degree. Fix: put backlash and stiffness on the spec sheet.
- Skipping the start-up peak. Inertia from a large boom or platform can exceed steady torque. Fix: include acceleration torque in the load figure.
How to Verify the Ratio After Selection
Selection ends on paper. Confirm it with a short test on a prototype or a sample unit before volume ordering. We accept sample orders for this purpose, and standard products start at an MOQ of one set.
- Time the move. Run the full move at rated load. Pass: it finishes inside the required time with the motor below its rated current.
- Test repeatability. Approach the same target from both directions, ten times each. Pass: the spread fits your accuracy target. If not, revisit backlash and the choice of single or double worm.
- Log temperature. Run your real duty cycle until the housing temperature levels off. Pass: it stays below the limit in the drive's technical file. If not, revisit the ratio, duty cycle, or frame size.
- Test the hold. Stop under load and watch for drift on the feedback device. Pass: no drift in your test window. If not, add a brake or review the lead angle.
Field cases show why the last check matters. A South Korean port equipment manufacturer placed a repeat order for 20 units of WEA9-62-25HR single worm slew drives. Their port crane systems needed tracking precision of 0.15° or better, an IP65 seal, and self-locking. A Canadian forestry equipment manufacturer ordered 30 units of WED14-86-25BHR.5 double worm slew drives for grapple machines with precision of 0.13° or better.
Behind both orders is the same checking routine. Each of our slew bearings passes CMM three-coordinate inspection and dynamic load testing, and you can read more about slew drive quality control on our site. Confirmed manufacturing defects are replaced free of charge under our 2-year extended warranty.
When the Procedure Changes: Single Worm, Double Worm, and Custom Ratios
The method above applies to any worm gear slew drive. Only three variations change the steps.
- Double worm for tighter backlash. A double worm slew drive uses two worm shafts so you can preload the mesh. Choose it when your accuracy target is near the single-worm limit or when the load reverses often. A Houston, Texas manufacturer ordered 150 units of WED17-104-25HR double worm slew drives for heavy-duty wheel steering. See the WED slew drive series for that format.
- Two motors, one load. With two worm shafts, you split the input torque. Redo step 3 per motor, and check that both motors share load evenly.
- Non-catalog ratio. If the speed window and torque check leave no standard ratio, a customized slew drive is the next move. Customized orders start at 5 sets, and we send a technical proposal within 24 hours of receiving your load, speed, and environment data.
Environment also changes the specification. Our slew drives offer protection up to IP66 and anti-corrosion ratings up to C4H. We select materials per working condition from ductile cast iron, alloy steel, stainless steel, and forged alloy steel. Share the load, speed, and site conditions, and our engineering team will reply within 48 hours.
You are done when one ratio passes the speed, resolution, torque, and heat checks, and the prototype test confirms the move time, repeatability, temperature, and hold. If you are looking for a worm slew drive supplier, Luoyang Slewring Bearing Co., Ltd. can review your calculation and quote the matching drive. Send us your load, motor speed, and duty cycle to get the latest quotation.
Request Your Custom Slew Drive or Bearing Spec
Tell us your load, speed, and environment — receive a tailored 100–5000 mm slewing drive or slewing bearing proposal with 3D drawings within 24 hours.